How to Remove Scratches From Motorcycle Helmet Visor?

how to remove scratches from motorcycle helmet visor

The helmet visor is the most important safety equipment on your motorcycle. It protects you from the sun, wind, rain, and other weather elements. A scratched visor can make it difficult for you to see the road ahead, which could lead to an accident.

If you have a motorcycle helmet with a scratched visor, you should get it repaired as soon as possible. If you have a scratched motorcycle helmet visor, then you need to read this article to find out how to remove the scratches and restore your visor to its original condition.

What is the Scratch on Your Motorcycle Helmet Visor?

There are a few reasons why you might have scratched your visor. One of the most common reasons is that dirt and debris from the road get caught between the visor and the helmet. This causes scratches on the surface of the visor.

In addition, if you have a motorcycle helmet with a face shield, it’s possible to scratch your visor by accident when taking off or putting on your helmet.

The other reason for scratching your visor is that it’s been in contact with something sharp such as tree branches or rocks. It’s also possible to scratch it when cleaning it with a cloth or paper towel.

Read More: How To Change Your AGV Helmet’s Visor

How to Remove Small Scratches from Your Motorcycle Helmet Visor

Step 1: Find the Scratch

If you notice a small scratch on your helmet visor, the first thing you should do is find it. The best way to do this is to look at the surface of your helmet visor.

Step 2: Remove the Visor Cover

As I have said, the visor cover is attached with a screw and a lock. You must remove the lock and the screw to remove the visor cover.

Step 3: Clean the Visor

If you use a damp cloth to remove the scratch, then you should clean the visor after you’ve finished removing the scratch. This will prevent dirt from getting stuck on the visor.

Step 4: Reinstall the Visor Cover

After you have cleaned the visor, you should reattach the visor cover. This is done by screwing the lock back into place and tightening the screw.

Step 5: Spray the Visor with a Waterproofing Spray

After you have cleaned your helmet visor, you should spray it with a waterproofing spray. This will prevent the visor from getting damaged by the elements.

Step 6: Let the Visor Dry

Once you have finished spraying the visor, you should let it dry. This will prevent the visor from getting dirty again.

Step 7: Test the Visor

Once the visor has dried, you should test it to see if it has gotten the scratch out. If the visor is still scratched, then you should repeat the steps above.

Check Also: How to Put Bluetooth on a Motorcycle Helmet for Hands-free Communications

How to Remove Heavy-Duty Scratches from Your Motorcycle Helmet Visor

Heavy-duty scratches on your motorcycle helmet visor are a big problem. They are also hard to repair, so removing them before they get too bad is best.

Motorcycle helmets are a crucial part of a biker’s safety gear. However, no matter how well you take care of it, your helmet will eventually get scratched.

This guide will teach you how to remove heavy-duty scratches from your motorcycle helmet visor.

Step 1:

  • Clean the surface with water and dish detergent
  • Wash the surface with a wet sponge or cloth
  • Rinse thoroughly and dry with a soft cloth

Step 2:

  • Apply to rub alcohol to the surface 
  • Rub in circular motions until all the scratches disappear 
  • Rinse thoroughly and dry with a soft cloth

Step 3:

  • Apply polish to the surface
  • Polish the surface with a clean cloth until the scratches reappear
  • Repeat steps 2 and 3 as necessary

Check Also: How To Use Motorcycle Helmet Lock To Protect Your Ride

How To Prevent Scratches On Helmet Visor?

Helmet visors can get scratched easily, leading to visibility issues. Here are a few tips on how to prevent scratches from happening: 

  1. Always use protective gear when working with any type of metal, especially when using a tool. This includes wearing gloves and using a dust mask. 
  2. Do not touch the helmet visor or reflectors with your hands. Instead, use a cloth or tool to clean them off. 
  3. Be careful when moving the helmet around; do not bang it against something else or pull on the straps too hard. 
  4. Store the helmet in a safe place when not in use.

How do you maintain a helmet visor?

How do you maintain a helmet visor?

Helmet visors are a safety feature of helmets that protect riders from wind and rain. The visor should be cleaned regularly to prevent it from becoming foggy or scratched. It can also be damaged by debris, so keeping it in good condition is important.

 To clean the visor, use a mild soap and water solution. Be sure to dry the surface afterwards. If the visor becomes scratched or damaged, replace it with a new one.

Read More: How to Paint a Motorcycle Helmet.

Can you use toothpaste on a helmet visor?

Can you use toothpaste on a helmet visor?

The answer is yes; you can use toothpaste on a helmet visor. However, you may not want to.

In general, toothpaste is safe to use on most surfaces. However, helmets are made of plastic and other materials that can break down quickly, so it’s essential to be careful when cleaning them.

If toothpaste is applied too aggressively or if the visor is scratched or scuffed, it could damage the helmet. It’s also essential to avoid contact with the eyes if toothpaste is accidentally applied to the face shield.

Read More: How to Choose Helmet Color?

How to remove tint from helmet visor?

Tinted helmet visors are a popular way to protect your vision while riding a bike. However, if you want to remove the tint from your helmet visor, there are several methods that you can try.

A hair dryer is one way to remove tint from a helmet visor. Ensure the hair dryer is set on low heat and hold it against the side of the helmet visor for about 10 seconds.

Another method is using rubbing alcohol. Again, ensure that the alcohol is set on low heat and apply it to the side of the helmet visor for about 10 seconds.

Finally, you can use a steamer. Again, ensure that the steamer is set on low heat and hold it against the side of the helmet visor for about 10 seconds.

Check Also: How To Tint A Motorcycle Helmet Visor – Easy Steps

How To Remove Iridium Tint Off A Helmet Visor?

If you want to remove the iridium tint from your helmet visor, there are a few steps that you’ll need to take.

  1. You’ll need some rubbing alcohol.
  2. You’ll need a cloth or paper towel.
  3. You’ll need a light-coloured cloth or paper towel to cover the visor.
  4. Use rubbing alcohol to clean the visor.
  5. Use a light-coloured cloth or paper towel to dry the visor.
  6. Apply a clear sealant to any scratches on the visor and let it dry completely.
  7.  Reattach the visor using the screws that came with your helmet.
  8. Enjoy your new clean helmet!

Can You Polish A helmet Visor?

Polishing a helmet visor is not as difficult as it may seem. A few simple steps can be followed to achieve the desired outcome.

First, use a mild soap and water mixture to clean the visor. Make sure to get into all the nooks and crannies of the surface.

Next, use a soft cloth or microfiber cloth to buff the visor until it is shiny and reflective. Finally, use an appropriate polish to seal the finish and protect it from further wear and tear.

How long do scratches last on a motorcycle helmet visor?

Scratches on a motorcycle helmet visor can last for a while, depending on the severity. If the scratch is small, it might only last a day or two. However, if the scratch is deeper and wider, it might last for weeks or even months.

Ultimately, it depends on how deep and wide the scratch is.

FAQ of Remove Scratches from Motorcycle Helmet Visor

How do I remove scratches from my motorcycle helmet visor?  

I have used a lot of different things to try to remove scratches from my helmet visor. The best thing I have found is to use a microfiber cloth and warm water.

Is it possible to permanently remove a scratch on my motorcycle helmet visor?

Yes, it is possible to remove a scratch on your motorcycle helmet visor permanently.

How do I know if the scratch is on the visor or the helmet?

If the scratch is on the visor, you can use a microfiber cloth and warm water. If the scratch is on the helmet, you’ll need to take it off and examine it.

What should I do if I can’t get the scratch out?

If you can’t remove the scratch, you can cover it with a clear, waterproof coating.


In conclusion, if you’re looking to protect your visor, you need to look at the quality of your material. Many motorcycle visors are made from polycarbonate, which is very resistant to scratches.

 If you’re looking for a visor that will last, check out this article on removing scratches from motorcycle helmet visors.

Similar Posts


  1. Pingback: How to Clean Bike Helmet – Protection Pick
    1. That’s a great point! When it comes to helmets, it’s important to consult the manufacturer’s instructions for guidance on how long they are designed to last and provide optimal protection. While it can vary depending on the specific helmet and its usage, manufacturers typically recommend replacing helmets every 3-5 years.

      Over time, helmets can experience wear and tear, and their ability to provide adequate protection may diminish. The materials used in helmets, such as foam liners, can deteriorate due to factors like exposure to sunlight, sweat, and impact forces. Therefore, it’s crucial to follow the manufacturer’s guidelines to ensure you’re using a helmet that offers the intended level of protection.

      Additionally, if a helmet has been involved in a significant impact or accident, it’s advisable to replace it even if it’s within the recommended timeframe. Hidden damage may compromise its effectiveness, and it’s always better to err on the side of caution when it comes to safety equipment.

      Remember, the manufacturer’s instructions should be your primary source of information regarding the lifespan and maintenance of your helmet.

Leave a Reply

Your email address will not be published. Required fields are marked *